Top 10 Best microphone for arduino [2022]

1. ARCELI 2pcs Electret Microphone Amplifier, GY-MAX4466 Breakout Sensor with Adjustable Gain Control for Arduino

  • 1. This breakout is best used for projects such as voice changers, audio recording/sampling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain. You can set the gain from 25x to 125x.
  • 2. Add an ear to your project with this well-designed which has excellent power supply noise rejection.
  • 3. Using is simple: connect GND to ground, VCC to 2.4-5VDC. For the best performance, use the “quietest” supply available (on an Arduino, this would be the 3.3V supply).
  • 4.For audio-reactive projects, we suggest using an FFT driver library which can take the audio input and ‘translate’ it into frequencies.

2. 10 Pieces Electret Microphone Amplifier Adjustable MAX4466 Module Microphone Preamplifier Blue Breakout Board Compatible with Arduino

  • Application: the MAX4466 microphone breakout is suitable for voice converters, audio recording and sampling, and audio response projects using FFT; On the back, there is a small trimmer pot to adjust the gain; You can set the gain from 25x to 125x
  • Parameters: power supply voltage: +2.4V to +5.5V (can be compatible with STM, Raspberry Pi and other development board motherboards); Power supply rejection ratio: 112dB; Common mode rejection ratio: 126dB; AVOL: 125dB (RL = 100 thousands of ohm meter) rail-to-rail output; Quiescent power supply current: less than 24 microamp; Gain bandwidth: 600kHz
  • 20-20KHz electret microphone soldered on: comes with a 20-20KHz electret microphone soldered on the board for audio-reactive projects; It is recommended to use the FFT driver library, which can take audio input and ‘translate’ it into frequencies
  • Easy to use: connect GND to ground, VCC to 2.4-5VDC; For the good performance, use the ‘quietest’ supply available (this would be the 3.3V supply)
  • Power supply noise rejection function: the amplifier has good power supply noise rejection

3. SparkFun RedBoard Artemis Nano Machine Learning Development Board Includes BLE 1 megabyte of Flash USB-C Qwiic I2C MEMS Microphone Compatible with Arduino IDE TenserFlow Models Small Footprint

  • A light weight, 0.8mm thick PCB, with on board LiPo-battery charging and a Qwiic connector
  • Dual row of ground connections make it easy to add lots of buttons, LEDs, and anything that requires its own GND connection
  • Fully compatible with the SparkFun’s compatible with Arduino core and can be programmed easily under the Arduino IDE platform
  • With 1MB flash and 384k RAM you’ll have plenty of room for your sketches.
  • The Artemis module runs at 48MHz with a 96MHz turbo mode available and compatible with Bluetooth to boot. FCC/IC/CE Certified 8/16/2019 (ID Number 2ASW8-ART3MIS)

4. DAOKI 5PCS High Sensitivity Sound Microphone Sensor Detection Module for Arduino AVR PIC

  • There is a mounting screw hole 3mm.
  • Use 5v DC power supply
  • There are threshold level output flip.
  • Real-time output of the microphone voltage signal / DO. when the sound intensity reaches a threshold
  • The output high and low signal threshold – Sensitivity potentiometer adjustmen. Application:Microphone sound detection

5. DEVMO 3PCS Mic Microphone Sensor High Sensitivity Sound Detection Module Compatible with A-rduino PIC AVR

  • ★Microphone Sensor High Sensitivity Sound Detection Modules for A-rduino PIC AVR
  • ★Uses 5V DC power supply
  • ★Has 3mm mounting screw hole
  • ★Has two outputs: AO, analog output, real-time output voltage signal of the microphone
  • ★Package Includes:3pcs Microphone Sensor High Sensitivity Sound Detection Module

6. Cylewet 10Pcs Cylindrical Electret Condenser Microphone Pickup with 2 Pins 9×7mm for Arduino (Pack of 10) CYT1013

  • Diameter: 9mm/ 0.35inches
  • Length: 7mm/ 0.28inches
  • Sensitivity: -48-66dB
  • Frequency Range: 50 20KHz
  • Current Consumption: Max 500uA

7. HiLetgo 2pcs Electret Microphone Amplifier MAX4466 Module Adjustable Gain Blue Breakout Board for Arduino

  • The board comes with a 20-20KHz electret microphone soldered on
  • Using the MAX4466, an op-amp specifically designed for amplifier
  • For the best performance, use the “quietest” supply available (on an for Arduino, this would be the 3.3V supply)
  • The amplifier has excellent power supply noise rejection
  • This breakout board is best used for projects such as voice changers, audio recordingmpling, and audio-reactive projects that use FFT

8. Comimark 2Pcs MAX9814 Electret Microphone Amplifier Module AGC Auto Gain Control for Arduino

  • Supply Voltage: 2.7v-5.5v @ 3mA current
  • Output: 2Vpp on 1.25V bias
  • Frequency Response: 20Hz – 20 KHz
  • Package included: 2PCS x MAX9814 Microphone AGC Amplifier Board Module (If the number of products received is incorrect, please contact us . we will refund or give you a replacement)
  • We highly appreciate all customers opinions to improve the selling, also if anything you unsatisfied, please contact us for probable best solution.

9. Anmbest 5PCS RED Microphone Sensor AVR PIC High Sensitivity Sound Detection Module LM393 Dual Differential Comparators Output for Arduino

  • PRODUCT ADVANTAGES: The main chip is LM393. Signal is clean, waveform is good, driving ability is strong.
  • ADJUSTABLE THRESHOLD: Build in potentiometer can be used to adjust the threshold level.
  • EASY TO USE, INTUITIVE: When sound intensity exceed a certain threshold, produces low(Digital output 0) signal and light will be off, Otherwise output high(Digital output 1) signal and light will be bright.
  • EASY TO INSTALL: There is a mounting screw hole, convenient fixed.
  • WIDELY APPLICATIONS: a variety of platforms including Arduino / AVR / ARM/PIC.

10. GY-MAX4466 Electret Microphone Amplifier Sensor Sound Module with Adjustable Gain Control for Arduino (Pack of 2)

  • MAX4466 microphone breakout is best used for projects such as voice changers, audio recording/sampling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain. You can set the gain from 25x to 125x.
  • Add an ear to your project with this well-designed which has excellent power supply noise rejection.
  • Using is simple: connect GND to ground, VCC to 2.4-5VDC. For the best performance, use the “quietest” supply available.
  • For audio-reactive projects, we suggest using an FFT driver library which can take the audio input and ‘translate’ it into frequencies.
  • If you have any problem, please contact seller as follow: click “DIYmalls”(you can find “Sold by DIYmalls” under Buy Now button), in the new page, click “Ask a question”.